The following printing technologies are routinely found in modern printers, as of April 2006:
Toner-based printers
Toner-based printers work using the Xerographic principle that is at work in most photocopiers: by adhering toner to a light-sensitive print drum, then using static electricity to transfer the toner to the printing medium to which it is fused with heat and pressure.
The most common type of toner-based printer is the laser printer, which uses precision lasers to cause adherence. Laser printers are known for high quality prints, good print speed, and a low (Black and White) cost-per-copy; they are the most common printer for many general-purpose office applications. They are far less commonly used as consumer printers due to a high initial cost, although this cost is dropping.
Laser printers are available in both color and monochrome varieties.
Another toner based printer is the LED printer which uses an array of LEDs instead of a laser to cause toner adhesion to the print drum.
Recent research has also indicated that Laser printers emit potentially dangerous ultrafine particles, possibly causing health problems associated with respiration and cause pollution equivalent to cigarettes. The degree of particle emissions varies with age, model and design of each printer but is generally proportional to the amount of toner required. Furthermore, a well ventilated workspace would allow such ultrafine particles to disperse thus reducing the health side effects.
Liquid inkjet printers
Solid ink printers
Solid Ink printers, also known as phase-change printers, are a type of thermal transfer printer. They use solid sticks of CMYK colored ink (similar in consistency to candle wax), which are melted and fed into a piezo crystal operated print-head. The printhead sprays the ink on a rotating, oil coated drum. The paper then passes over the print drum, at which time the image is transferred, or transfixed, to the page.
Solid ink printers are most commonly used as color office printers, and are excellent at printing on transparencies and other non-porous media. Solid ink printers can produce excellent results. Acquisition and operating costs are similar to laser printers. Drawbacks of the technology include high power consumption and long warm-up times from a cold state.
Also, some users complain that the resulting prints are difficult to write on (the wax tends to repel inks from pens), and are difficult to feed through Automatic Document Feeders, but these traits have been significantly reduced in later models. In addition, this type of printer is only available from one manufacturer, Xerox, manufactured as part of their Xerox Phaser office printer line. Previously, solid ink printers were manufactured by Tektronix, but Tek sold the printing business to Xerox in 2001
Dye-sublimation printers
A dye-sublimation printer (or dye-sub printer) is a printer which employs a printing process that uses heat to transfer dye to a medium such as a plastic card, paper or canvas. The process is usually to lay one color at a time using a ribbon that has color panels. Dye-sub printers are intended primarily for high-quality color applications, including color photography; and are less well-suited for text. While once the province of high-end print shops, dye-sublimation printers are now increasingly used as dedicated consumer photo printers.
Inkless printers
Inkless printers use paper with colorless dye crystals embedded between the two outer layers of the paper. When the printer is turned on, heat from the drum causes the crystals to colorize at different rates and become visible. One inkless printing technology, Zink, originally developed at Polaroid, became available in 2007. Because of the way it prints, the printer can be as small as a business card, the images are waterproof, and in fact, one product slated for release by Zink Imaging is a digital camera with a printer built into it.
Xerox is also working on an inkless printer which will use a special reusable paper coated with a few micrometres of UV light sensitive chemicals. The printer will use a special UV light bar which will be able to write and erase the paper. As of early 2007 this technology is still in development and the text on the printed pages can only last between 16-24 hours before fading.
Obsolete and special-purpose printing technologies
The following technologies are either obsolete, or limited to special applications though most were, at one time, in widespread use.
Thermal printers work by selectively heating regions of special heat-sensitive paper. These printers are limited to special-purpose applications such as cash registers and the printers in ATMs and gasoline dispensers. They are also used in some older inexpensive fax machines.
Impact printers rely on a forcible impact to transfer ink to the media, similar to the action of a typewriter. All but the dot matrix printer rely on the use of formed characters, letterforms that represent each of the characters that the printer was capable of printing. In addition, most of these printers were limited to monochrome printing in a single typeface at one time, although bolding and underlining of text could be done by overstriking, that is, printing two or more impressions in the same character position. Impact printers varieties include, Typewriter-derived printers, Teletypewriter-derived printers, Daisy wheel printers, Dot matrix printers and Line printers. Dot matrix printers remain in common use in businesses where multi-part forms are printed, such as car rental service counters.
Pen-based plotters were an alternate printing technology once common in engineering and architectural firms. Pen-based plotters rely on contact with the paper (but not impact, per se), and special purpose pens that are mechanically run over the paper to create text and images.
Typewriter-derived printers
Several different computer printers were simply computer-controllable versions of existing electric typewriters. The Friden Flexowriter and IBM Selectric typewriter were the most-common examples. The Flexowriter printed with a conventional typebar mechanism while the Selectric used IBM's well-known "golf ball" printing mechanism. In either case, the letter form then struck a ribbon which was pressed against the paper, printing one character at a time. The maximum speed of the Selectric printer (the faster of the two) was 15.5 characters per second.
Teletypewriter-derived printers
The common teleprinter could easily be interfaced to the computer and became very popular except for those computers manufactured by IBM. Some models used a "typebox" that was positioned (in the X- and Y-axes) by a mechanism and the selected letter from was struck by a hammer. Others used a type cylinder in a similar way as the Selectric typewriters used their type ball. In either case, the letter form then struck a ribbon to print the letterform. Most teleprinters operated at ten characters per second although a few achieved 15 CPS.
Daisy wheel printers
Daisy-wheel printers operate in much the same fashion as a typewriter. A hammer strikes a wheel with petals (the daisy wheel), each petal containing a letter form at its tip. The letter form strikes a ribbon of ink, depositing the ink on the page and thus printing a character. By rotating the daisy wheel, different characters are selected for printing.
These printers were also referred to as letter-quality printers because, during their heyday, they could produce text which was as clear and crisp as a typewriter (though they were nowhere near the quality of printing presses). The fastest letter-quality printers printed at 30 characters per second.
Dot-matrix printers
In the general sense many printers rely on a matrix of pixels, or dots, that together form the larger image. However, the term dot matrix printer is specifically used for impact printers that use a matrix of small pins to create precise dots. The advantage of dot-matrix over other impact printers is that they can produce graphical images in addition to text; however the text is generally of poorer quality than impact printers that use letterforms (type).
A Tandy 1000 HX with a Tandy DMP-133 dot-matrix printer.
Dot-matrix printers can be broadly divided into two major classes:
Ballistic wire printers (discussed in the dot matrix printers article)
Stored energy printers
Dot matrix printers can either be character-based or line-based (that is, a single horizontal series of pixels across the page), referring to the configuration of the print head.
At one time, dot matrix printers were one of the more common types of printers used for general use - such as for home and small office use. Such printers would have either 9 or 24 pins on the print head. 24-pin print heads were able to print at a higher quality. Once the price of inkjet printers dropped to the point where they were competitive with dot matrix printers, dot matrix printers began to fall out of favor for general use.
Some dot matrix printers, such as the NEC P6300, can be upgraded to print in color. This is achieved through the use of a four-color ribbon mounted on a mechanism (provided in an upgrade kit that replaces the standard black ribbon mechanism after installation) that raises and lowers the ribbons as needed. Color graphics are generally printed in four passes at standard resolution, thus slowing down printing considerably. As a result, color graphics can take up to four times longer to print than standard monochrome graphics, or up to 8-16 times as long at high resolution mode.
Dot matrix printers are still commonly used in low-cost, low-quality applications like cash registers, or in demanding, very high volume applications like invoice printing. The fact that they use an impact printing method allows them to be used to print multi-part documents using carbonless copy paper (like sales invoices and credit card receipts), whereas other printing methods are unusable with paper of this type. Dot-matrix printers are now (as of 2005) rapidly being superseded even as receipt printers.
Line printers
Line printers, as the name implies, print an entire line of text at a time. Three principal designs existed. In drum printers, a drum carries the entire character set of the printer repeated in each column that is to be printed. In chain printers (also known as train printers), the character set is arranged multiple times around a chain that travels horizontally past the print line. In either case, to print a line, precisely timed hammers strike against the back of the paper at the exact moment that the correct character to be printed is passing in front of the paper. The paper presses forward against a ribbon which then presses against the character form and the impression of the character form is printed onto the paper.
Comb printers represent the third major design. These printers were a hybrid of dot matrix printing and line printing. In these printers, a comb of hammers printed a portion of a row of pixels at one time (for example, every eighth pixel). By shifting the comb back and forth slightly, the entire pixel row could be printed (continuing the example, in just eight cycles). The paper then advanced and the next pixel row was printed. Because far less motion was involved than in a conventional dot matrix printer, these printers were very fast compared to dot matrix printers and were competitive in speed with formed-character line printers while also being able to print dot-matrix graphics.
Line printers were the fastest of all impact printers and were used for bulk printing in large computer centres. They were virtually never used with personal computers and have now been replaced by high-speed laser printers.
The legacy of line printers lives on in many computer operating systems, which use the abbreviations "lp", "lpr", or "LPT" to refer to printers.
Pen-based plotters
A plotter is a vector graphics printing device which operates by moving a pen over the surface of paper. Plotters have been (and still are) used in applications such as computer-aided design, though they are being replaced with wide-format conventional printers (which nowadays have sufficient resolution to render high-quality vector graphics using a rasterized print engine). It is commonplace to refer to such wide-format printers as "plotters", even though such usage is technically incorrect.
No comments:
Post a Comment